T-piece Cable Tray ECT100 100x150 SS304
Variations
Product information
| Suitable for cable tray height : | 100 mm |
|---|---|
| Suitable for cable tray width : | 150 mm |
| Construction type : | T-piece horizontal |
| For connection with screws : | Yes |
| For screwless connection : | No |
| Model : | Integrated connector |
| Inner radius : | 50 mm |
| Material : | Stainless steel |
| Material quality : | Rustproof and acidproof steel |
| Colour : | Stainless steel |
T-piece ECTET100 is an accessory for the ECT100 cable tray system and is used to create a horizontal branch within cable routes. This accessory enables cables to be distributed in three directions while maintaining a continuous and mechanically stable cable support structure. The T-piece is suitable for heavy industrial, utility, and infrastructure installations where structured cable distribution is required.
The standard version is manufactured from hot dip galvanized carbon steel according to NEN-EN-ISO 1461, with a minimum zinc coating thickness of 60 µm, suitable for heavy industrial and outdoor environments. The hot dip galvanizing process is applied after fabrication and provides full surface protection, including cut edges and fixing holes. This ensures reliable corrosion protection under increased mechanical and environmental loads, in accordance with IEC 61537 and installations compliant with NEN 1010.
The T-piece is designed as a fixed horizontal fitting for direct connection to ECT100 cable trays. The execution is equipped with integrated connectors and is supplied including 24x EFS08x15 fixing set (carriage bolt M08x15, nut, and washer), enabling fast and alignment-stable installation. The accessory is fully compatible with other ECT100 system components and ensures a uniform and continuous cable tray installation.
Technical Specifications
- Product type: T-piece for cable tray with equal widths
- System: ECT100
- System height: 100 mm
- System width: 100 to 600 mm
- Material thickness: 1.0 to 1.5 mm
- Angle: 90°
- Radius: 50 mm
- Connector perforation: 25 x 8.5 mm
- Bottom perforation: 25 x 8.5 mm
- Material: Carbon steel
- Surface finish: Hot dip galvanized according to NEN-EN-ISO 1461
- Zinc coating thickness: minimum 60 µm
- Connection method: Bolted
- Execution: With integrated connectors, including 24x EFS08x15 fixing set (carriage bolt M08x15, nut, and washer)
- Standards: IEC 61537, applicable within installations compliant with NEN 1010
- Construction type: Horizontal T-piece
- Top cover: No
- Side perforation: No
- Bottom perforation: Yes
Typical Applications
- Horizontal branching within cable tray systems
- Distribution of cable routes in three directions
- Heavy industrial and outdoor installations
- Utility and infrastructure cable routes
Available Material Variants
- HDG: Hot dip galvanized carbon steel according to NEN-EN-ISO 1461, with a minimum zinc coating thickness of 90 µm, suitable for heavy industrial and outdoor environments.
- PG: Pre galvanized carbon steel according to EN 10346, suitable for dry indoor environments and light industrial applications.
- Stainless steel 304 (A2 / 1.4301): Stainless steel for indoor environments and lightly corrosive conditions.
- Stainless steel 316 (A4 / 1.4404): Stainless steel with enhanced corrosion resistance for chemical, maritime, and offshore applications.
Complementary Products
For a complete installation within the ECT100 system, the following components are relevant:
- Cable trays: ECT100 cable trays in various widths
- Couplers: For longitudinal connections
- Bends and accessories: For direction changes
- Brackets: Wall, ceiling, and trapeze brackets
- Covers and clamps: For protection and fixation
These components together ensure a safe, compatible, and maintenance-friendly installation.
Other widths, radii and angles available on request.
ECT100_Cable Tray 100mm_Overview
ECTET100_Equal T-Piece SAT